Samsung SLM4583FX код ошибки
17.02.2020 182 0.0 0
  • Code: 11-2T01, 11-2T11, 11-2T21
  • Display:Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch
  • Description:Paper in tray is not matched to the machine paper setting.
  • Remedy:1) Check and change the paper setting of the corresponding tray properly.
  • Code: 11-2T31, 11-2T41, 11-2T61
  • Display:Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch
  • Description:Paper in tray is not matched to the machine paper setting.
  • Remedy:1) Check and change the paper setting of the corresponding tray properly.
  • Code: 61–1111
  • Display:Booting Failure: #61-1111. Turn off then on. Call for service if the problem persists
  • Description:Hibernation image creation is failed.
  • Remedy:1) Turn the machine on with a normal booting. 2) Enter the SVC mode. Select “Hibernation On” again.
  • Code: A1–1112, A1–1113
  • Display:Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists
  • Description:Main(Feed/Fuser) motor operation is abnormal.
  • Remedy:• A1–1112 : Main motor is not operated for print-job. • A1–1113 : Main motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Check if there are any foreign substances or paper around the paper path. 2) Remove the right cover. 3) Check if the main motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the main motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the main(feed/fuser) motor(JC31–00144B) • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)). - If the control signal is abnormal, replace the main board(JC92–02722A). b) If the motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. 5) If the main motor operation is normal, remove the fuser unit. Check if the fuser unit has any problem. Replace the fuser unit(JC91–01177A (220V) / JC91–01176A (110V)).
  • Code: A1–2112, A1–2113

  • Display:Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists
  • Description:OPC/Deve motor operation is abnormal.
  • Remedy:• A1–2112 : OPC/Deve motor is not operated for print-job. • A1–2113 : OPC/Deve motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Check if there are any foreign substances or paper around the paper path. 2) Remove the right cover. 3) Check if the OPC/Deve motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the OPC/Deve motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the OPC/Deve motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the OPC/Deve motor(JC31–00075C). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)). - If the control signal is abnormal, replace the main board(JC92–02722A). b) If the OPC/Deve motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. 5) If the OPC/Deve motor operation is normal, remove the imaging unit. Check if the imaging unit has any problem. Replace the imaging unit.
  • Code: A1-5110
  • Display:Motor Failure: #A1-5110. Turn off then on. Call for service if the problem persists
  • Description:Supply motor operation is abnormal.
  • Remedy:1) Turn the machine off. 2) Remove the right cover. 3) Check if the DC motor (toner supply motor) connector in the main drive unit is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the DC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the DC motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the DC motor(JC31-00078A) or the main drive unit(JC93–00923A). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)). - If the control signal is abnormal, replace the main board(JC92–02722A). b) If the DC motor is operational, • If the value on the main board is abnormal, replace the main board. If the value is normal, replace the harness.
  • Code: A2–1210, A2–2110
  • Display:Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists
  • Description:SMPS or Fuser or LSU or Deve fan is not operational.
  • Remedy:NOTE • SMPS fan error : A2–1210 • Main(Fuser) fan error : A2–2110 • LSU fan error : A2–2410 • Deve fan error : A2–2610 1) Turn the machine off. 2) Check if the corresponding fan connector is connected correctly 3) If the connection is OK, Enter SVC mode and execute fan test. (Diagnostics > Engine Diagnostics > Engine Test Routines) 4) If the fan is not operational, measure the fan power. a) If 24V power is generated, replace the defective fan. • SMPS fan : JC31–00153A • Main(Fuser) fan : JC31–00088A • LSU fan : JC31–00086A • Deve fan : JC31–00086A b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02722A). 5) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan.
  • Code: A2–2410, A2–2610
  • Display:Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists
  • Description:SMPS or Fuser or LSU or Deve fan is not operational.
  • Remedy:NOTE • SMPS fan error : A2–1210 • Main(Fuser) fan error : A2–2110 • LSU fan error : A2–2410 • Deve fan error : A2–2610 1) Turn the machine off. 2) Check if the corresponding fan connector is connected correctly 3) If the connection is OK, Enter SVC mode and execute fan test. (Diagnostics > Engine Diagnostics > Engine Test Routines) 4) If the fan is not operational, measure the fan power. a) If 24V power is generated, replace the defective fan. • SMPS fan : JC31–00153A • Main(Fuser) fan : JC31–00088A • LSU fan : JC31–00086A • Deve fan : JC31–00086A b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02722A). 5) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan.
  • Code: A3–3212
  • Display:Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists
  • Description:Inner temperature sensor is defective.
  • Remedy:1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) 2) Measure the resistance value of the connector at both ends. If the value is not in 47.5K - 52.5K (@ 25C), replace the inner temp sensor(1404-001417). 3) If the sensor is normal, replace the main board(JC92.02722A).
  • Code: A3–3312, A3–3320
  • Display:Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists The room temperature is not suitable for this set use. Please adjust room temperature
  • Description:Outer temperature/humidity sensor is defective.
  • Remedy:1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines > Outer Temperature) 2) Measure the resistance value of the connector at both ends. If the value is not in 47.5K - 52.5K(@ 25C), replace the outer temperature/humidity sensor(JC32-00005A). 3) If the harness and sensor are normal, replace the main board(JC92.02722A).
  • Code: A4-1110
  • Display:Lamp Failure: #A4-1110. Open the door, then close it. Call for service if the problem persists
  • Description:Erase Lamp does not turn on.
  • Remedy:1) Enter SVC mode. Execute the erase lamp test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Erase Lamp) 2) If the erase lamp does not turn on, replace it(JC92-02373A).
  • Code: C1–1110, C1–111A
  • Display:Prepare new toner cartridge Shake toner cartridge and then install. Replace toner cartridge if the problem persists
  • Description:Toner cartridge is almost empty.
  • Remedy:1) Open the front cover. 2) Remove the toner cartridge. 3) Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 4) Reinstall the toner cartridge. 5) Close the front cover. 6) Prepare new toner cartridge because it will be exhausted soon.
  • Code: C1–1120, C1–1140

  • Display:Replace with new toner cartridge. End of life, Replace with new toner cartridge.
  • Description:Toner cartridge is at the end of its life.
  • Remedy:1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the front cover.
  • Code: C1–1160, C1–1170
  • Display:Replace with new toner cartridge. End of life, Replace with new toner cartridge.
  • Description:Toner cartridge is at the end of its life.
  • Remedy:1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the front cover.
  • Code: C1–1311, C1–1313, C1–1314
  • Display:Toner Cartridge Failure: #C1-1311. Install toner cartridge again. Shake toner cartridge and then install.
  • Description:The toner supply is abnormal.
  • Remedy:1) Turn the machine off then on. 2) Open the front cover. 3) Remove the toner cartridge. Thoroughly roll the cartridge three or four times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 4) Try to print out the sample page more than 20 pages. 5) Check the toner cartridge. • Check if the toner cartridge is installed correctly. • Check if the toner seal is removed perfectly. • Check if the toner supply shutter between the toner cartridge and the imaging unit works normally. 6) Replace the toner cartridge. Print out the sample page. 7) Check the toner supply motor operation. • Check the signal and power with the DVM. • If the checked result is normal, replace the DC motor(JC31-00078A) or the main drive unit(JC93–00923A).
  • Code: C1–1411
  • Display:Toner cartridge is not installed. Install the cartridge.
  • Description:The toner cartridge is not installed properly.
  • Remedy:1) Open the front cover. 2) If the toner cartridge is not installed, install it. Try to test the machine again. 3) If the toner cartridge is installed, remove it. Check if the modular jack is contaminated or broken. 4) Clean the modular jack or replace the toner cartridge. 5) If it is OK, check the CN22 harness connection on the main board. 6) If the harness is defective, replace it. 7) Turn the machine off then on. Try to test the machine.
  • Code: C1–1512
  • Display:Toner cartridge is not compatible. Check users guide.
  • Description:Toner cartridge is not compatible.
  • Remedy:1) Open the front cover. Remove the toner cartridge. 2) Check if the label information of the toner cartridge is same with the machine’s one. (ex. /SEE) 3) If label information is different from the machine or the toner cartridge is not a samsung genuine, replace it with a new one.
  • Code: C1–1712
  • Display:Toner Cartridge Failure: #C1-1712. Call for service
  • Description:The data of CRUM is not detected. / CRUM is defective.
  • Remedy:1) Open the front cover. Check if the toner cartridge is installed. 2) Remove and reinstall the toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the toner cartridge with new one.
  • Code: C3–1110
  • Display:Prepare new imaging unit.
  • Description:Imaging unit has almost reached the end of its life.
  • Remedy:1) Prepare the new imaging unit because it will be exhausted soon.
  • Code: C3–1120, C3–1140
  • Display:Replace with new imaging unit End of life, Replace with new imaging unit.
  • Description:Imaging unit is at the end of its life.
  • Remedy:1) Open the front cover. 2) Remove the imaging unit and replace it with new one. 3) Close the front cover.
  • Code: C3–1150, C3–1170

  • Display:Replace with new imaging unit End of life, Replace with new imaging unit.
  • Description:Imaging unit is at the end of its life.
  • Remedy:1) Open the front cover. 2) Remove the imaging unit and replace it with new one. 3) Close the front cover.
  • Code: C3–1312
  • Display:Imaging Unit Failure: #C3-1312. Install imaging unit again.
  • Description:Toner sensor is defective. The machine can’t detect the sensor signal in the imaging unit normally.
  • Remedy:1) Install the genuine samsung imaging unit. 2) If the imaging unit is already installed, check the following. • Reinstall the toner cartridge and imaging unit. • Check if the CRUM connector is normal. • Turn the machine off then on.
  • Code: C3–1330, C3–1411, C3–1414
  • Display:Imaging Unit Failure: #C3-1330. Install imaging unit again. Imaging unit is not installed. Install the unit Imaging Unit Failure: #C3-1414. Install imaging unit again.
  • Description:The imaging unit is not installed properly.
  • Remedy:1) Open the front cover. 2) If the imaging unit is not installed, install it. Try to test the machine again. 3) If the imaging unit is installed, remove it. Check if the modular jack is contaminated or broken. 4) Clean the modular jack or replace the imaging unit. 5) If it is OK, check the CN22 harness connection on the main board. 6) If the harness is defective, replace it. 7) Turn the machine off then on. Try to test the machine.
  • Code: C3–1512
  • Display:Imaging unit is not compatible. Check users guide.
  • Description:Imaging unit is not compatible.
  • Remedy:1) Open the front cover. 2) Remove and reinstall the imaging unit. 3) Close the front cover. 4) If the problem persists, replace the imaging unit with new one.
  • Code: C3–1712
  • Display:Imaging unit Failure: #C3-1712. Call for service.
  • Description:The data of CRUM is not detected.
  • Remedy:1) Open the front cover. 2) Remove the imaging unit check that its modular jack is contaminated or deformed. 3) If it is defective, replace it with new one. 4) Close the front cover.
  • Code: C6–1120
  • Display:Replace with new fuser unit
  • Description:Fuser unit is at the end of its life.
  • Remedy:1) Turn the machine off. 2) Open and remove the rear cover. 3) Remove the fuser unit(JC91–01177A (220V) / JC91–01176A (110V)) and replace it with new one. 4) Close the rear cover.
  • Code: H1-1210, H1-1211
  • Display:Paper jam in Tray 2.
  • Description:Paper jam has occurred in tray2.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray2 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray2 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness.
  • Code: H1-1212, H1-1213
  • Display:Paper jam in Tray 2.
  • Description:Paper jam has occurred in tray2.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray2 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray2 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness.
  • Code: H1-1222

  • Display:Tray 2 cassette is pulled out. Insert it properly.
  • Description:Tray 2 is pulled out or the cassette detection sensor connector is not connected or broken.
  • Remedy:1) Remove and insert tray2 correctly. 2) If the problem persists, remove tray2 again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 5) If the problem persists, replace the SCF board(JC92-02754A).
  • Code: H1-1230, H1-1240
  • Display:Input System Failure: #H1-1230. Check tray 2 connection. Tray 2 is not installed. Install the tray.
  • Description:The communication error between the tray 2 and the main machine has occurred.
  • Remedy:1) Turn the machine off. 2) Check the connection on SCF board. Reconnect the harness. 3) If the drawer connector is deformed or broken, replace it. (AS-HARNESS HSCF : JC81–09742A / HOLDER-CONNECTOR_SCF : JC61–01742A)) 4) If the problem persists, replace the SCF main board(JC92-02754A).
  • Code: H1-1251, H1-1252, H1-1254
  • Display:Paper is low in Tray 2. Load paper. Paper is empty in tray 2. Load paper.
  • Description:Paper in the tray2 is less than 10% of specification. / The photo sensor is defective.
  • Remedy:1) Remove tray2. Load the paper in tray2. 2) If paper is loaded but error message has not disappeared, check the following. a) Check if the paper empty sensor is contaminated. If so, clean it. b) If the paper empty sensor(0604-001325) is defective, replace it. c) If the empty actuator(JC66–02613A) is defective, replace it.
  • Code: H1-1253
  • Display:Input System Failure #H1-1253 : Pull Tray 2 out and insert it.
  • Description:The paper is not fed from tray2.
  • Remedy:1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A).
  • Code: H1-1310, H1-1311
  • Display:Paper jam in Tray 3.
  • Description:Paper jam has occurred in tray3.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray3 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray3 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness.
  • Code: H1-1312, H1-1313
  • Display:Paper jam in Tray 3.
  • Description:Paper jam has occurred in tray3.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray3 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray3 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness.
  • Code: H1-1322
  • Display:Tray 3 cassette is pulled out. Insert it properly.
  • Description:Tray 3 is pulled out or the cassette detection sensor connector is not connected or broken.
  • Remedy:1) Remove and insert tray3 correctly. 2) If the problem persists, remove tray3 again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 5) If the problem persists, replace the SCF board(JC92-02754A).
  • Code: H1-1330, H1-1340
  • Display:Input System Failure: #H1-1330. Check tray 3 connection. Tray 3 is not installed. Install the tray.
  • Description:The communication error between the tray 3 and the main machine has occurred.
  • Remedy:1) Turn the machine off. 2) Check the connection on SCF board. Reconnect the harness. 3) If the drawer connector is deformed or broken, replace it. (AS-HARNESS HSCF : JC81–09742A / HOLDER-CONNECTOR_SCF : JC61–01742A)) 4) If the problem persists, replace the SCF main board(JC92-02754A).Code: H1-1351, H1-1352, H1-1354
  • Display:Paper is low in Tray 3. Load paper. Paper is empty in tray 3. Load paper.
  • Description:Paper in the tray3 is less than 10% of specification. / The photo sensor is defective.
  • Remedy:1) Remove tray2. Load the paper in tray3. 2) If paper is loaded but error message has not disappeared, check the following. a) Check if the paper empty sensor is contaminated. If so, clean it. b) If the paper empty sensor(0604-001325) is defective, replace it. c) If the empty actuator(JC66–02613A) is defective, replace it.
  • Code: H1-1353
  • Display:Input System Failure #H1-1353 : Pull Tray 3 out and insert it.
  • Description:The paper is not fed from tray3.
  • Remedy:1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A).
  • Code: H1-1410, H1-1411
  • Display:Paper jam in Tray 4.
  • Description:Paper jam has occurred in tray4.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray4 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray4 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) Check if the Press D-cut of the Gear-Lifting(JC81-08478A) is broken. 8) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 9) If the problem persists, replace the Drop connector harness.
  • Code: H1-1412, H1-1413
  • Display:Paper jam in Tray 4.
  • Description:Paper jam has occurred in tray4.
  • Remedy:1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray4 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray4 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) Check if the Press D-cut of the Gear-Lifting(JC81-08478A) is broken. 8) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 9) If the problem persists, replace the Drop connector harness.

Теги:Samsung SLM4583FX error code, Samsung SLM4583FX код ошибки


Читайте также:
Комментарии
comments powered by HyperComments