Samsung SLM4075FX код ошибки
17.02.2020 176 0.0 0
  • Code: A1-1110
  • Display:Error: #A1-1110 / Motor Failure: #A1-1110. Turn off then on. Call for service if the problem persists
  • Description:Harness or main BLDC motor or main board is defective. / OPC coupler in the toner cartridge(or imaging unit) has overloaded.
  • Remedy:1) Turn the machine off then on. If the error persists, refer to the following. 2) Remove the right cover. 3) Check if the motor connector on main board is connected properly. Reconnect it. 4) OPC coupler has overloaded. After removing the toner cartridge/imaging unit, rotate the OPC coupler. If there is any damage, the OPC coupler can’t rotate well. Replace the toner cartridge/imaging unit. 5) Remove the left cover. 6) Remove the main drive unit. (Refer to 3.3.14) 7) The main BLDC motor is defective. a) Unplug the connector from the motor carefully. b) Replace the main BLDC motor (JC31-00075A)with new one. 8) If the problem persists, replace the main board.
  • Code: C1-1110
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1120
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1144
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1150

  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1160
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1170
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:NOTE These errors are for M3375/3875/4075. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C1-1310
  • Display:Error: #C1-1310 / Toner Failure: #C1-1310. Install toner again Toner Not Installed / Toner cartridge is not installed. Install it
  • Description:The toner cartridge is not installed.
  • Remedy:These errors are for M3375/3875/4075. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the toner cartridge is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the toner cartridge with new one.
  • Code: C1-1411
  • Display:Error: #C1-1310 / Toner Failure: #C1-1310. Install toner again Toner Not Installed / Toner cartridge is not installed. Install it
  • Description:The toner cartridge is not installed.
  • Remedy:These errors are for M3375/3875/4075. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the toner cartridge is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the toner cartridge with new one.
  • Code: C1-1512
  • Display:Toner Not Compatible / Toner cartridge is not compatible. Check guide
  • Description:Toner cartridge is not compatible.
  • Remedy:This error is for M3375/3875/4075. 1) Open the front cover. 2) Remove the toner cartridge. 3) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C1-1710
  • Display:Error: #C1-1710 / Toner Cart Failure: #C1-1710. Call for service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3375/3875/4075. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C1-1711
  • Display:Error: #C1-1711 / Toner Cart Failure: #C1-1711. Call for service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3375/3875/4075. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C1-1712

  • Display:Error: #C1-1712 / Toner Cart Failure: #C1-1712. Call for service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3375/3875/4075. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C2-1110
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:These errors are for M3370/3870/4070/4072FD. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C2-1120
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:These errors are for M3370/3870/4070/4072FD. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C2-1150
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:These errors are for M3370/3870/4070/4072FD. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C2-1160
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:These errors are for M3370/3870/4070/4072FD. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C2-1170
  • Display:Prepare new toner / Prepare new toner cartridge Replace new toner / Replace with new toner cartridge Replace new toner / End of life, Replace with new toner cartridge
  • Description:The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life.
  • Remedy:These errors are for M3370/3870/4070/4072FD. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one.
  • Code: C2-1411
  • Display:Toner Not Installed / Toner cartridge is not installed. Install it
  • Description:The toner cartridge is not installed.
  • Remedy:This error is for M3370/3870/4070/4072FD. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the toner cartridge is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the toner cartridge with new one.
  • Code: C2-1512
  • Display:Toner Not Compatible / Toner cartridge is not compatible. Check guide
  • Description:Toner cartridge is not compatible.
  • Remedy:This error is for M3370/3870/4070. 1) Open the front cover. 2) Remove the toner cartridge. 3) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C2-1710

  • Display:Error: #C2-1710 Call for Service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3370/3870/4070. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C2-1711
  • Display:Error: #C1-1711 Call for Service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3370/3870/4070. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C2-1712
  • Display:Error: #C1-1712 Call for Service
  • Description:The machine can’t detect the CRUM chip of the toner cartridge.
  • Remedy:These errors are for M3370/3870/4070. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.
  • Code: C3-1110
  • Display:Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit
  • Description:The remaining imaging unit is less than 10% / The imaging unit is at the end of its life.
  • Remedy:These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one.
  • Code: C3-1120
  • Display:Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit
  • Description:The remaining imaging unit is less than 10% / The imaging unit is at the end of its life.
  • Remedy:These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one.
  • Code: C3-1144
  • Display:Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit
  • Description:The remaining imaging unit is less than 10% / The imaging unit is at the end of its life.
  • Remedy:These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one.
  • Code: C3-1410
  • Display:IMG. Not Installed / Imaging unit is not installed. Install the unit
  • Description:The imaging unit is not installed
  • Remedy:This error is for M3325/3825/4025. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the imaging unit is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the imaging unit with new one.
  • Code: C3-1510
  • Display:IMG. Not compatible / Imaging unit is not compatible. Check guide
  • Description:Imaging unit is not compatible.
  • Remedy:This error is for M3320/3820/4020. 1) Open the front cover. 2) Remove the toner cartridge and imaging unit. 3) If the imaging unit is not a Samsung genuine imaging unit, replace with new one.
  • Code: C9-1112

  • Display:Replace pickup roller / Replace with new tray 1 pickup roller
  • Description:Tray1 pick up roller is worn out.
  • Remedy:1) Remove the tray 1 cassette. 2) Remove the duplex unit. 3) Pull the small tap down, then release the pick up roller(JC73-00340A). 4. Alignment and Troubleshooting
  • Code: C9-1115
  • Display:Replace retard roller / Replace with new tray 1 retard roller
  • Description:Tray1 reverse roller is worn out.
  • Remedy:1) Remove the tray1 cassette. 2) Remove the reverse roller(JC90-01032A).
  • Code: C9-1122
  • Display:Replace pickup roller / Replace with new tray 2 pickup roller
  • Description:Tray2 pick up roller is worn out.
  • Remedy:1) Remove the Tray 2 cassette. 2) See the bottom of the SCF Unit. 3) Pull the small tap down, then release the pick up roller(JC97-02259A).
  • Code: C9-1125
  • Display:Replace retard roller / Replace with new tray 2 retard roller
  • Description:Tray2 reverse roller is worn out.
  • Remedy:1) Remove the Tray 2 cassette. 2) Open the cassette cover. 3) Pull the small tap down, then release the reverse roller(JC97-02259A).
  • Code: H1-1210
  • Display:Paper jam in Tray2.
  • Description:A paper jam was detected in the feed area of the tray2.
  • Remedy:1) Remove the Tray2 cassette. 2) Find and remove the jammed paper. 3) If the problem persists, check the following. • Check if the pick up/forward/reverse roller(JC97-02259A) is contaminated or worn out. • Check if the feed sensor connector is connected properly. • If the feed sensor(0604-001325) is defective replace it.
  • Code: H1-1220
  • Display:Tray 2 Door Open. Close it
  • Description:Optional cassette is not installed properly
  • Remedy:1) Remove and reinstall the Tray2 cassette. 2) Check the cassette detection sensor. • Check if the connection between sensor and main board is OK. Reconnect the harness. • If the sensor(JC34-00001A) is defective, replace it. 3) If the problem persists, replace the SCF main board(JC92-02636A).
  • Code: H1-1230
  • Display:Error: #H1-1230 / Input System Failure: #H1-1230. Check tray 2 connection
  • Description:Communication error has occurred.
  • Remedy:1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Remove the SCF right cover. (Refer to 3.3.23.1) 4) Check if the interface connector is connected to the SCF main board. If the interface connector is defective, replace it. 5) If the problem persists, replace the SCF main board.(JC92-02636A)
  • Code: H1-1240
  • Display:Tray2 Not Install
  • Description:Optional cassette is not installed properly.
  • Remedy:1) Remove and reinstall the Tray2 cassette. 2) Check the cassette detection sensor. • Check if the connection between sensor and main board is OK. Reconnect the harness. • If the sensor(JC34-00001A) is defective, replace it. 3) If the problem persists, replace the SCF main board(JC92-02636A).
  • Code: H1-1252

  • Display:Paper empty in tray 2 / Paper is empty in tray 2. Load paper
  • Description:There is no paper in the tray2. / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray2. 2) If the problem persists, turn the machine off and check the following. 3) If the Actuator-Paper Empty is defective, replace it. 4) If the Photo Sensor(0604-001325) is defective, replace it. Check if the connector is connected properly. 5) If the problem persists, replace the SCF main board.(JC92-02636A)
  • Code: H1-1254
  • Display:Paper empty in tray 2 / Paper is empty in tray 2. Load paper
  • Description:There is no paper in the tray2. / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray2. 2) If the problem persists, turn the machine off and check the following. 3) If the Actuator-Paper Empty is defective, replace it. 4) If the Photo Sensor(0604-001325) is defective, replace it. Check if the connector is connected properly. 5) If the problem persists, replace the SCF main board.(JC92-02636A)
  • Code: M1-1110
  • Display:Paper Jam in Tray1.
  • Description:The jammed paper has occurred in the tray1.
  • Remedy:1) Clear the jammed paper. If the problem persists, check the following. 2) While pushing the Paper Empty Sensor, send the printing data. Check if the pick up roller is rotating normally. 3) Check if there is any obstacles in the paper path (from Pick-Up to Feed Sensor). The feed roller should be especially checked. 4) Print out the Supplies Information. Check the Tray 1 Roller Life and Tray1 Reverse(Retard) roller Life. If the life came to the end, replace the relative roller.
  • Code: M1-1610
  • Display:Paper Jam in MP tray.
  • Description:The jammed paper has occurred in the MP tray.
  • Remedy:1) Clear the jammed paper. If the problem persists, check the following. 2) Turn the machine off. 3) Remove the right cover. 4) Check if the MP Unit connector is connected properly. 5) Remove the MP Unit. Check if the MP rollers are worn out. If necessary, replace the defective roller or MP unit.
  • Code: M1-5112
  • Display:Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
  • Description:There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.
  • Code: M1-5113
  • Display:Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
  • Description:There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.
  • Code: M1-5120
  • Display:Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper
  • Description:There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.
  • Code: M1-5612
  • Display:Paper empty in MP / Paper is empty in MP tray. Load paper
  • Description:There is no paper in the MP tray (or Manual Feeder). / Actuator-Paper Empty or photo sensor is defective.
  • Remedy:1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.
  • Code: M1-5712

  • Display:Paper Empty in manual feeder / Paper is empty in manual feeder. Load paper
  • Description:There is no paper in the MP tray (or Manual Feeder). / Actuator-Paper Empty or photo sensor is defective
  • Remedy:1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board.
  • Code: M2-1110
  • Display:Jam inside machine
  • Description:A paper jam was detected at the feed sensor.
  • Remedy:1) Remove the jammed paper. (Refer to 4.1.3) If the error persists, check the followings. 2) Check if the feed sensor connector is connected properly. 3) Check if the Regi roller is contaminated or worn out. If yes, replace it. 4) Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it.
  • Code: M2-2210
  • Display:Jam inside of duplex
  • Description:A paper jam was detected in the bottom of duplex.
  • Remedy:1) Remove the jammed paper. 2) Remove the contamination or obstacles in the paper path. 3) If this jam error occur continually, replace the duplex unit.
  • Code: M3-1110
  • Display:Jam in exit area
  • Description:A paper jam was detected in the exit area.
  • Remedy:1) Remove the jammed paper. 2) Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it. 3) Check if the exit roller rubber is worn out. Replace the exit roller(JC93-00323A). 4) Check if the exit sensor connector is connected properly. If the connection is OK, replace the exit sensor.
  • Code: M3-2130
  • Display:Output bin full / Output bin full. Remove printed paper
  • Description:The machine detected that the output tray has got full or the bin-full sensor is defective.
  • Remedy:1) Remove the paper on the output tray. 2) If the problem persists, check the followings. 3) Remove top cover. 4) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor.
  • Code: S1-2411
  • Display:Error: #S1-2411 / HDD System Failure: #S1-2411. Turn off then on. Call for service if the problem persists
  • Description:HDD installation is abnormal / HDD is defective.
  • Remedy:1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Check if the HDD cable is connected correctly. 4) If the HDD is defective, replace it.
  • Code: S1-4210
  • Display:Error: #S1-4210 / Video System Failure: #S1-4210. Turn off then on. Call for service if the problem persists
  • Description:Fax communication error has occurred.
  • Remedy:1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Check the harness connection between main board and fax board. 4) If the connection is OK, replace the fax board.
  • Code: S2-4120
  • Display:Door open. Close it.
  • Description:Door is open or the cover open switch is defective.
  • Remedy:1) Check if the front door is closed correctly. 2) Check if the rear door is closed correctly. 3) Check if the connection between the main board and HVPS board is correct. 4) Check if the cover open switch on HVPS board is operated properly. If it is defective, replace the HVPS board(JC44-00197A).
  • Code: S3-3122

  • Display:Scanner Locked / Scanner is locked. Press Stop button
  • Description:Scanner lock error has occurred. CIS does not move.
  • Remedy:1) Check if the CIS unit is moving when power on. 2) Check if the flat cable is connected to the CIS unit properly. Re-connect or replace the cable. 3) If the CIS is defective, replace it. 4) Check if there is any defective part in the scanner unit. (Gear, Belt, Motor etc.) 5) If the problem persists, replace the main board.
  • Code: S4-2111
  • Display:Memory Full / Fax memory is almost full. Print or remove received fax job
  • Description:The fax memory is almost full.
  • Remedy:1) Print or remove the received fax job in Secure Recieve.
  • Code: S4-2112
  • Display:Memory Full / Fax memory is full. Print or remove received fax job
  • Description:The fax memory is almost full.
  • Remedy:1) Print or remove the received fax job in Secure Recieve.
  • Code: S6-3123
  • Display:Network Problem: IP Conflict.
  • Description:IP address conflicts with that of other system. / There is no response when checking the ping test.
  • Remedy:Change the machine’s IP address. • Set-up the IP address in this order, Network -> TCP/IP (IPv4) -> STATIC. • In case of DHCP or Bootp, reboot the machine to receive a new IP address.
  • Code: S6-3128
  • Display:802.1x Network Error
  • Description:The confirmation was requested for wired port, the server has rejected. / The confirmation protocol is not the same or user information (ID/Password) is wrong.
  • Remedy:Check the setting-up for 802.1x confirmation server. • Re-enter the server information and confirmation protocol. • Re-enter the user information.
  • Code: U1-2315
  • Display:Error #U1-2315 Turn off then on.
  • Description:The temperature control of fuser unit is abnormal.
  • Remedy:1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V)
  • Code: U1-2320
  • Display:Error #U1-2320 Turn off then on.
  • Description:The temperature control of fuser unit is abnormal.
  • Remedy:1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V)
  • Code: U1-2330
  • Display:Error #U1-2330 Turn off then on.
  • Description:The temperature control of fuser unit is abnormal.
  • Remedy:1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V)
  • Code: U1-2334

  • Display:Error #U1-2334 Turn off then on.
  • Description:The temperature control of fuser unit is abnormal.
  • Remedy:1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V)
  • Code: U1-2340
  • Display:Error #U1-2340 Turn off then on.
  • Description:The temperature control of fuser unit is abnormal.
  • Remedy:1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V)
  • Code: U2-1112
  • Display:Error #U2-1111 Turn off then on.
  • Description:LSU Motor does not work normally.
  • Remedy:1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board.
  • Code: U2-1113
  • Display:Error #U2-1113 Turn off then on.
  • Description:LSU Motor does not work normally.
  • Remedy:1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board.
  • Code: U3-3113, U3-3313, U3-3314
  • Display:Original paper jam / Original paper jam inside of scanner. Remove jam
  • Description:A document jam was detected in the ADF unit.
  • Remedy:1) Remove the jammed paper from ADF unit. 2) If the error persists, turn the machine off then on. 3) If the document jam occurs continually, open the ADF cover-top. Check if the ADF pick up roller is contaminated or worn out. Clean or replace it. 4) If the pick up roller is OK, check the followings. a) Check if the ADF motor is working normally. b) Check if the connector on the ADF joint board is connected correctly. 5) If the problem persists, replace the ADF unit.
  • Code: U3-3413, U3-3513, U3-3514
  • Display:Original paper jam / Original paper jam inside of scanner. Remove jam
  • Description:A document jam was detected in the ADF unit.
  • Remedy:1) Remove the jammed paper from ADF unit. 2) If the error persists, turn the machine off then on. 3) If the document jam occurs continually, open the ADF cover-top. Check if the ADF pick up roller is contaminated or worn out. Clean or replace it. 4) If the pick up roller is OK, check the followings. a) Check if the ADF motor is working normally. b) Check if the connector on the ADF joint board is connected correctly. 5) If the problem persists, replace the ADF unit.
  • Code: U3-4110
  • Display:Door of scanner is open.
  • Description:ADF top cover is opened.
  • Remedy:1) Close the ADF top cover.

Теги:Samsung SLM4075FX error code, Samsung SLM4075FX код ошибки


Читайте также:
Комментарии
comments powered by HyperComments