Brother DCP-L8450CDW код ошибки
26.11.2019 16 0.0 0
  • Code: 0100
  • Display:Print Unable 01 Turn the power off and then back on again.
  • Description:ASIC error or motor driver error occurred.
  • Remedy:1 Main PCB failure Replace the main PCB ASSY.
  • Code: 0201
  • Display:Print Unable 02 Turn the power off and then back on again.
  • Description:Synchronization signal from the main motor cannot be detected. Or the main motor speed is unstable after a set period of time.
  • Remedy:1 Connection failure of the main motor harness Reconnect the main motor harness. 2 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 3 Part in the process drive unit damaged Replace the process drive unit. 4 Fuser unit damaged Replace the fuser unit. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.
  • Code: 0202
  • Display:Print Unable 02 Turn the power off and then back on again.
  • Description:Synchronization signal from the process motor cannot be detected. Or the process motor speed is unstable after a set period of time.
  • Remedy:1 Connection failure of the process motor harness Reconnect the process motor harness. 2 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 3 Part in the process drive unit damaged Replace the process drive unit. 4 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 5 Main PCB failure Replace the main PCB ASSY.
  • Code: 0300
  • Display:Print Unable 03 Turn the power off and then back on again.
  • Description:The Lock signal of the polygon motor of the laser unit cannot be detected.
  • Remedy:1 Connection failure of the polygon motor harness Reconnect the polygon motor harness. 2 Laser unit failure Replace the laser unit. 3 Main PCB failure Replace the main PCB ASSY.

 Code: 0401

  • Display:Print Unable 04 Turn the power off and then back on again.
  • Description:BD sensor 1 damaged.
  • Remedy:1 Connection failure of the polygon motor harness Reconnect the polygon motor harness. 2 Laser unit failure Replace the laser unit. 3 Main PCB failure Replace the main PCB ASSY.
  • Code: 0402
  • Display:Print Unable 04 Turn the power off and then back on again.
  • Description:BD sensor 4 damaged.
  • Remedy:1 Connection failure of the polygon motor harness Reconnect the polygon motor harness. 2 Laser unit failure Replace the laser unit. 3 Main PCB failure Replace the main PCB ASSY.
  • Code: 0501
  • Display:Print Unable 05 Turn the power off and then back on again.
  • Description:The center thermistor of the fuser unit does not reach the specified temperature within the specified time.
  • Remedy:< User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
    1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY.
  • Code: 0502
  • Display:Print Unable 05 Turn the power off and then back on again.
  • Description:After the temperature of the fuser unit rises to a certain level, the temperature of the center thermistor does not reach the specified temperature within the specified period of time in the next step.
  • Remedy:< User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
    1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY.

Теги:Brother DCP-L8450CDW error code, Brother DCP-L8450CDW код ошибки

Читайте также:
Комментарии
Добавлять комментарии могут только зарегистрированные пользователи.
[ Регистрация | Вход ]